0. INTRODUCTION
1. SCOPE
   1. Functional definition
   2. Field of application
   3. Principles
2. REFERENCES
3. TERMS AND DEFINITIONS
4. MESSAGE DEFINITION
   1. Data segment clarification
   2. Data segment index (alphabetical sequence)
   3. Message structure
      1. Segment table

This specification provides the definition of the Product exchange reconciliation message (PRODEX) to be used in Electronic Data Interchange (EDI) between trading partners involved in administration, commerce and transport.

This paper provides the definition of the United Nations Standard Product Exchange Message to be used in Electronic Data Interchange (EDI) between trading partners.

The Product Exchange Message is a communication between two trading partners with agreements for the loan of products to each other, to provide information about movements of products from and to various locations on particular dates.

The message gives additional information on the outstanding balances of each product between the trading partners.

No financial value is attached to the products and settlement is usually carried out between like products.

The Product Exchange Message may be applied for both national and international trade. It is based on universal commercial practice within the petroleum industry and may eventually be of interest to other industries.

Each product exchange is covered by a bilateral contract and exchange accounts are balanced at agreed period ends.

Each contract will define the units in which the product (or group of products) should be measured. This is known as The Unit of Account.

A transaction forms the basis on which Product Exchanges are reconciled. A Transaction is defined as: a change of product title supported by the required data set for Delivery note/Ticket; or subsequently agreed Adjustments, Rebrands or Transfers.

There may be many transactions within an accounting period.

The product exchanged is identified by its product name, supply location, mode of transport, and date.

See UNTDID, Part 4, Chapter 2.6 UN/ECE UNSM - General Introduction, Section 1.

See UNTDID, Part 4, Chapter 2.6 UN/ECE UNSM - General Introduction, Section 2.

This section should be read in conjunction with the Branching Diagram and the Segment Table which indicate mandatory, conditional and repeating requirements.

The following guidelines and principles apply to the whole message and are intended to facilitate the understanding and implementation of the message:

All specified dates/times should be in the format 'yymmdd'/'hhmm' unless all parties involved in the transaction agree that there is a functional requirement for an alternative format. Periods should be specified as whole numbers representing the required period as indicated in the format qualifier (weeks, months, etc.)

Where a choice of code or text is given only the code element should be used wherever possible.

Due to the high volume of data that will be usually trasnmitted in the Sales Data Report message, it is highly recommended to use codes for products and locations. Conditional data that is not required in the message should not be included.

Care must be taken that the segment qualifier in dependent segments do not conflict with the segment qualifier of the trigger segment of a group.

0010 | UNH, Message header

A service segment starting and uniquely identifying a message. The message type code for the Product exchange reconciliation message is PRODEX.

Note: Product exchange reconciliation messages conforming to this document must contain the following data in segment UNH, composite S009:

0020 BGM, Beginning of message

A segment to indicate the type and function of the Product Exchange Message and to transmit its unique identifying number.

0030 DTM, Date/time/period

A segment identifying the date and time that the statment was generated and the end period to which the transaction statement refers.

0040 MEA, Measurements

This identifies the primary unit of account pertaining to the contract.

0050 NAD, Name and address

A segment identifying the two partners involved in the transaction identified in the following message. In this message the segment is mandatory and must appear twice; once for each partner.

0060 Segment Group 1: RFF-DTM

A segment group to give the relevant exchange references (contract number with -if necessary- its dates) relating to the whole message.

0070 RFF, Reference

A segment identifying the product exchange contract reference.

0080 DTM, Date/time/period

A segment specifying general dates and, when relevant, times related to the reference.

0090 Segment Group 2: IMD-QTY-SG3

A group of segments giving transaction details of the product groups exchanged and opening and closing balances for the accounting period (or as a result of the transactions).

0100 IMD, Item description

A segment identifying the product group exchanged between the interchange partners.

0110 QTY, Quantity

A segment identifying the exchange balances for the contract during the period. It is used for opening balances and for closing balances.

0120 Segment Group 3: LIN-GIS-LOC-DTM-MEA-QTY-TDT-SG4

A group of segments giving transaction details for each exchange transaction effected during the period.

0130 LIN, Line item

A segment identifying the product exchanged between the interchange partners.

0140 GIS, General indicator

A segment identifying the transaction type (receipt, delivery etc) and (where required) duty status.

0150 LOC, Place/location identification

A segment identifying e.g. the oil terminal location involved in sending and receiving the product.

0160 DTM, Date/time/period

A segment identifying the date of supply.

0170 MEA, Measurements

A segment identifying measurement information for the product exchanged.

0180 QTY, Quantity

A segment identifying the quantity(ies) for the product exchanged.

0190 TDT, Details of transport

A segment identifying the transport mode and appropriate movement identifier(s) for transaction.

0200 Segment Group 4: RFF-DTM

A group of segments identifying some unique number for each transaction.

0210 RFF, Reference

A segment identifying the consignment note, ticket reference or some unique number for each transaction.

0220 DTM, Date/time/period

A segment specifying general dates and, when relevant, times related to the reference.

0230 UNT, Message trailer

A service segment ending a message, giving the total number of segments in the message and the control reference number of the message.